ES Windows Kitchen Remodeling Nationwide

ES Windows Kitchen Remodeling: The Long Beach Owner’s Guide

ES Windows kitchen remodeling in Long Beach typically runs $14,000-$45,000 for a full project, with partial updates starting lower. We stock and install ES Windows-compatible frames, sashes, hardware, and sealed units, and we carry common replacement parts on our trucks for Belmont Shore, Bixby Knolls, and Naples service calls. Most ES Windows kitchen units we see fail at the locking mechanism or the insulated glass seal, not the frame itself, which is why matching the series number matters before we quote.

Call (424) 567-7009

Which ES Windows Models This Applies To

ES Windows produces aluminum and vinyl window systems in several series, and the kitchen application usually involves their 3000, 5000, or 8000 series lines. The 3000 series is a single-hung vinyl unit common in Long Beach tract homes built between 1995 and 2010. The 5000 series is an aluminum-clad vinyl hybrid with a thicker frame wall, usually found in custom or semi-custom homes from the 2000s forward. The 8000 series is their impact-rated line, required in some Long Beach zones near the coast for wind-borne debris protection.

To identify your series, open the sash and look for the etched code in the glass corner or the sticker on the frame head. The code begins with “ES-” followed by four digits. The 3000 series uses a 2-1/4″ frame depth; the 5000 series uses 2-3/4″; the 8000 series uses 3-1/4″ and carries a Miami-Dade NOA number, which you’ll need if you’re replacing an impact unit in a coastal zone. We do not need the NOA for a standard kitchen replacement, but we do need the exact frame depth to order the correct jamb extension kit.

Rowan Construction Group Long Beach is an independent service provider, not affiliated with ES Windows. We source OEM parts through ES Windows distributors in Anaheim and Ontario, and we also stock quality aftermarket equivalents from C.R. Laurence and Truth Hardware where the OEM lead time exceeds two weeks. The aftermarket route saves $40-$80 per sash on hardware, but we only use it when the spec matches the original load rating.

Signs Your ES Windows Kitchen Remodeling Is Failing

• The sash won’t stay open or slams shut. This is usually a failed balance shoe or broken coil spring in the jamb liner. In Long Beach’s salt air, the metal balance assemblies corrode faster than inland ratings suggest, especially on east-facing kitchen windows that catch morning marine layer moisture.
• Fog between the glass panes that won’t wipe away. The insulated glass unit (IGU) seal has failed. Once the desiccant inside the spacer bar saturates, condensation becomes permanent. ES Windows IGUs from the 2005-2015 era used a single-seal system that averaged 8-12 years in coastal California conditions, shorter than the 15-year rating.
• The lock engages but the sash still rattles in the wind. The keeper is worn or the frame has settled out of square. We check this with a 6-foot level on the sill; if the sill is out more than 1/8″ over that length, the window needs reframing, not just a new lock.
• Visible corrosion on the frame corners or weep holes. Aluminum frames pit where the anodized coating thins, usually at the bottom rail where water pools. In Long Beach, we see this accelerated on homes within a mile of the beach where salt deposits build up faster than the weep system can flush them.
• Draft even when fully closed. The weatherstrip has compressed or the sash bulb seal has torn. ES Windows uses a dual-fin weatherstrip on 5000 and 8000 series units; the 3000 series uses a simpler pile seal that flattens in 6-10 years under normal use.

Before

After

Replacement Cost & What’s Included

Kitchen remodels involving ES Windows replacement in Long Beach fall within our standard $14,000-$45,000 range, with window-specific line items broken out in every quote we write. A single ES Windows sash replacement runs $400-$900 installed, depending on series and whether the IGU or the entire sash is being swapped. Full-frame replacement of a kitchen window assembly runs $1,200-$2,800 per opening, including interior trim repair and exterior sealing.

What drives the range: frame material (vinyl vs. aluminum vs. impact-rated), whether the existing rough opening is square and dry, and whether interior drywall or exterior stucco repair is needed after the swap. Every quote we write includes the parts list, labor hours, and a photo record of the opening condition before we start. Under Clause 1 of the Haven Standard, the price is written before anyone picks up a tool, and no change proceeds without a signed change order.

DIY or Call Us?

There is one thing a homeowner can safely check: the series code and the rough opening dimensions. Write both down, photograph the label, and you’ll save us 15 minutes on the site visit. Everything else, we recommend against doing yourself.

Removing a vinyl sash from a 3000 series unit requires releasing the tilt latches while supporting the sash weight; if the balance is already failed, the sash drops hard and the glass can crack. The 5000 and 8000 series sashes are heavier, and the 8000 impact glass is laminated, which means a broken unit sends sharp glass and PVB interlayer fragments, not clean shards. The balance assemblies are under spring tension, and the 5000 series uses a constant-force coil that will unspool if the jamb liner is opened without a brake tool.

We carry 3000 and 5000 series hardware, balances, and common IGU sizes on our Long Beach trucks. For 8000 series impact units, we verify the NOA and order OEM, which typically takes 5-7 business days. Call (424) 567-7009 to schedule your free estimate. We’ll bring the parts catalog, measure the opening, and give you a written price before we leave.

FAQs