Quikrete Roofing Nationwide

Quikrete Roofing: The Long Beach Owner’s Guide

Quikrete roofing systems in Long Beach typically run $400-$1,800 for repairs and $8,000-$20,000 for full replacement, with most Quikrete-compatible underlayment and sealant parts stocked on our trucks for same-day install. We see these systems most often on flat or low-slope additions, ADUs, and garage conversions where the homeowner or original builder chose Quikrete’s waterproofing membrane products for cost control. The failure usually starts with bubbling or separation at seams, especially where the Long Beach marine layer keeps surfaces damp through June mornings.

Call (424) 567-7009

Most owners in Long Beach notice the problem after a rare heavy rain, when water pools where it never did before, or when a routine HVAC service call reveals saturated insulation above a Quikrete-coated roof deck. By then the substrate is often compromised, which is why we photograph everything before quoting.

Which Quikrete Models This Applies To

Quikrete’s roofing line is not model-numbered like a shingle system; it is identified by product series and application type. The two we encounter in Long Beach are the Quikrete Acrylic Elastomeric Roof Coating series (typically white, applied 10-20 mils dry) and the Quikrete Heavy Duty Waterproofing Cement used as a base layer on built-up or modified bitumen roofs. To identify what you have, check for a Quikrete label on any leftover bucket in the garage, or measure the coating thickness at a seam edge if accessible. Acrylic elastomeric will feel slightly flexible and rubbery; cementitious base layers will be hard and chalky.

The OEM-versus-aftermarket question matters less with Quikrete than with mechanical systems. Quikrete does not manufacture proprietary fasteners or edge metal; they specify standard galvanized drip edge and polyester fabric reinforcement. Where we deviate from strict OEM is in the topcoat. We often specify Henry 587 or Gardner-Gibson Sta-Kool elastomeric over a Quikrete base if the substrate condition warrants a higher solids content, which the manufacturer permits when the base layer is intact. We document this substitution in writing before application.

One compatibility gotcha in Long Beach: Quikrete’s acrylic line is not rated for direct ponding water. On dead-flat roofs without adequate slope to scuppers, we have seen 18-month failures even with proper mil thickness. We always check pitch with a digital level before specifying.

Signs Your Quikrete Roofing Is Failing

• Alligatoring or surface cracking. The acrylic topcoat develops a pattern of interconnected cracks as UV and salt air degrade the polymer. In Long Beach, this accelerates within two miles of the coast; we see it first on south- and west-facing exposures where afternoon sun is harshest.
• Bubbling or blistering between coats. Moisture vapor trapped in the substrate pushes up during warm afternoons. This means the base layer has lost adhesion, often at a plywood seam or over a previous patch.
• Soft spots when walked. The roof deck beneath the coating has absorbed water and begun to delaminate. We mark these with spray paint during inspection; they are rarely isolated to one spot.
• Flaking at penetrations. Pipe boots, vents, and HVAC curbs are the first failure points because Quikrete’s standard detail relies on hand-worked fabric reinforcement that is easy to under-apply. We find gaps in the polyester embedment on roughly half the Quikrete roofs we inspect in Belmont Shore and Alamitos Beach.
• Interior stains that appear after fog, not just rain. This is the tell for slow, vapor-driven leaks. Long Beach’s marine layer provides enough moisture to wick through a compromised membrane over hours, long before a storm would reveal it.

Before

After

Replacement Cost & What’s Included

Quikrete roof repair in Long Beach runs $400-$1,800 installed, depending on whether we are spot-sealing seams or stripping and re-coating a full section. Full tear-off and replacement with new substrate, where the Quikrete system has failed structurally, falls within our standard roof replacement range of $8,000-$20,000 for typical Long Beach footprints.

What drives the range: deck condition (plywood replacement adds $3-$5 per square foot), access difficulty (steep pitches or tight Long Beach lots), and whether we are matching an existing Quikrete finish or upgrading to a higher-performance system. Every quote is flat and written before work starts, under Clause 1 of the Haven Standard. No change proceeds without a signed change order.

DIY or Call Us?

There is one thing a Long Beach homeowner can safely check: the gutter and downspout flow. If water backs up and ponds against the roof edge, that accelerates Quikrete coating failure regardless of product quality. Clear the downspout and observe during the next rain.

Everything else belongs to a crew. Working on a low-slope roof still means edges, ladders, and often parapet walls with uncertain anchoring. The coating itself seems simple to roll on, but mil thickness is critical, Quikrete specifies wet-film measurement during application, and fabric embedment at seams is where untrained hands create the leaks that show up six months later. We have stripped and corrected enough homeowner Quikrete re-coats to know the savings rarely hold.

We carry Quikrete-compatible acrylic primer, polyester fabric, and elastomeric topcoat on our Long Beach trucks. Call (424) 567-7009 to schedule your free estimate. We will photograph the condition, measure the scope, and put the price in writing before anyone picks up a brush.

FAQs