Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Before
After
Before
After
Before
AfterHow Much Does New Window Installation Cost in Long Beach?
New window installation in Long Beach, CA typically runs $4,500 to $15,000 for a standard single-family home, depending on window count, frame material, and glass type. If you’re replacing standard double-hung vinyl windows throughout a three-bedroom home in Bixby Knolls or Signal Hill, expect to land somewhere in the middle of that range. Impact-rated windows – required or strongly recommended in some Long Beach coastal zones – carry a separate range of $8,000 to $25,000 for a whole-home project.
New Window Installation Cost Breakdown (2026)
New window installation in Long Beach costs between $4,500 and $15,000 for a typical residential project. The table below breaks that range into specific scope and material combinations so you can find the line that matches your situation before anyone arrives at your door.
| Project Scope / Window Type | Typical Long Beach Price Range |
|---|---|
| Single window replacement (standard vinyl, supply + install) | $400 – $850 |
| Single window replacement (fiberglass or wood-clad) | $700 – $1,600 |
| Whole-home window replacement, 8-12 windows (vinyl double-pane) | $4,500 – $9,000 |
| Whole-home window replacement, 8-12 windows (fiberglass) | $7,500 – $15,000 |
| Impact window installation, whole home | $8,000 – $25,000 |
| Single impact window (supply + install) | $900 – $2,200 |
| Bay or bow window installation | $2,200 – $6,500 |
| Egress window cut-in (new opening) | $1,800 – $4,500 |
| Sliding glass door converted to picture window | $1,200 – $3,500 |
| Permit (City of Long Beach, residential window work) | $150 – $500 per permit |
A few things worth understanding about these numbers. The low end of the whole-home range assumes a straightforward pocket replacement – your new window slides into the existing frame pocket without disturbing the surrounding stucco or drywall, which is common in the post-war tract homes that cover large parts of Lakewood Village and Wrigley. The high end applies when the existing frame is rotted, out-of-square, or when a new rough opening needs to be framed – work that shows up often in the older Craftsman and Spanish Revival homes along 4th Street and in Bluff Park. Labor in Long Beach runs roughly $75 to $140 per hour for a licensed installer, which is consistent with the broader Los Angeles County market but higher than inland San Bernardino County rates by about 20 to 30 percent.
Glass package is the other variable that moves the number fast. Standard double-pane low-e glass – the minimum most Long Beach homeowners should consider given the summer heat load from the inland thermal effect and the marine layer cycling – adds roughly $50 to $120 per window over basic single-pane. Triple-pane, which rarely makes economic sense in a coastal climate that never sees sustained extreme cold, adds another $80 to $200 per window.
What Affects New Window Installation Pricing in Long Beach
- Frame material. Vinyl is the most common choice in Long Beach and carries the lowest price – typically $180 to $450 per window for the unit itself. Fiberglass frames (brands like Pella and Milgard both offer strong fiberglass lines) run $350 to $900 per unit and hold up better in salt-air environments, which matters if your property is within a mile of the shoreline in Belmont Shore, Naples, or the Peninsula. Wood-clad frames cost the most and require the most maintenance in Long Beach’s coastal humidity.
- Window type and configuration. Double-hung, single-hung, and sliders are the least expensive configurations. Casements cost more because of the hardware. Bay and bow windows involve structural header work and cost significantly more – plan for $2,200 to $6,500 for a single bay unit fully installed.
- Pocket replacement vs. full-frame installation. A pocket replacement keeps the existing frame intact and finishes faster – one to two hours per window for a crew. A full-frame installation removes the entire frame down to the rough opening, which is necessary when framing is rotted or damaged. In Long Beach’s older housing stock – especially homes built before 1960 in Zaferia and the North Long Beach neighborhoods – full-frame work is more common than homeowners expect going in.
- Impact glass and coastal wind load requirements. Homes in Long Beach’s High Wind and Coastal Hazard zones may require windows that meet specific performance ratings under California Building Code Title 24. Impact-rated windows carry laminated glass with a PVB interlayer – similar construction to automotive safety glass – and the units themselves cost $300 to $900 more per window than standard double-pane. If your project is in a designated zone, the permit inspector will check the product specification sheet, so the brand and rating need to be on the written quote before work starts.
- Stucco repair and exterior finish work. Most Long Beach homes have stucco exteriors. When a frame is removed, the surrounding stucco needs to be cut back, a new weep screed installed at the sill, and the stucco patched and color-matched. This adds $150 to $400 per window opening and is a line item that shows up in Rowan’s written quotes because leaving it out is how surprise invoices happen.
- Permit and inspection requirements. The City of Long Beach requires permits for new window openings and for window replacements that change the rough opening size. Straight swap-in replacements in the same opening size are typically exempt from a permit but the project scope needs to be described accurately on the work order. Rowan pulls permits and schedules inspections as a standard step – it’s not an add-on and the cost is included in the written price before work starts.
- Window count and project size. Volume matters. A single-window replacement carries higher per-unit labor cost because setup, cleanup, and travel are spread across one opening. A whole-home project of eight to twelve windows spreads those fixed costs across every unit, which is part of why the per-window price drops on larger jobs. The written flat price Rowan provides before work begins reflects the actual window count, not an estimate that inflates at installation.
Before
AfterLong Beach-Specific Conditions That Affect Your Window Quote
Long Beach sits at the intersection of several climate and building-stock conditions that don’t appear in national cost guides. Understanding them helps you read a quote more accurately.
The marine layer that rolls in from the Pacific most mornings keeps surface temperatures moderate but creates sustained humidity at window frames, sill plates, and exterior trim. In Belmont Shore and Naples, where homes are often within four to six blocks of open water, aluminum frames oxidize and vinyl seals degrade faster than they do in inland neighborhoods like Lakewood or El Dorado Park. Fiberglass frames – Milgard’s Essence and Pella’s Impervia line are both solid options in this category – resist that cycling better than vinyl over a ten-year span. It’s a cost tradeoff worth putting numbers on: fiberglass costs $150 to $400 more per window upfront but typically holds its seal and finish longer in high-humidity coastal conditions.
Long Beach’s housing stock skews older. A significant portion of the single-family homes in the Rose Park Historic District, Wrigley, and Zaferia were built between 1920 and 1955 – which means original wood-frame single-pane windows, painted-over hardware, and in some cases, windows set into unreinforced masonry walls. Replacing windows in unreinforced masonry (URM) structures requires a structural assessment before framing work begins. This is not common to every Long Beach project, but it comes up in older North Long Beach homes more than contractors from outside the area tend to expect.
Title 24, California’s energy efficiency code, sets minimum thermal performance requirements for replacement windows. In Climate Zone 8, which covers most of Long Beach, the code requires a maximum U-factor of 0.30 and a maximum Solar Heat Gain Coefficient (SHGC) of 0.23 for replacement windows. Any window unit that doesn’t meet these specs won’t pass a permit inspection. The practical effect is that nearly every code-compliant replacement window in Long Beach today is double-pane low-e glass – the question is which grade of low-e coating and what frame material surrounds it.
How to Save on New Window Installation
The biggest savings on a Long Beach window project come from decisions made before the crew shows up, not during installation.
Bundle your window count. If you’re replacing three windows now and you know two more will need to go in the next two years, replacing all five in one project can reduce your per-unit cost by 15 to 25 percent. The material order is larger, the crew is already mobilized, and the stucco repair work is done in one pass. The written flat-price quote will show you exactly what the per-window number looks like at each volume, so you can make that call with real numbers.
Choose the right frame material for the location, not the lowest sticker price. Vinyl is the correct choice for most inland Long Beach neighborhoods. But if you’re in Belmont Shore or on the Peninsula and you buy vinyl to save $150 per window, you may be resealing or replacing sooner than you’d expect in a drier climate. The upfront savings can evaporate over a seven-to-ten-year horizon.
Get a permit when one is required. This sounds like spending money to save money, and it is. Unpermitted window work in Long Beach can complicate a home sale – the City’s building department has records, and buyers’ inspectors check them. More practically, unpermitted window openings that are later flagged can require the work to be redone to current code at the homeowner’s expense. The permit cost ($150 to $500) is real, but it’s small relative to that risk.
Use the Free Second Opinion. Rowan offers a free second opinion on any written estimate – bring a competitor’s quote and Grant Rowan’s team will go through it line by line at no charge. This is useful if you’ve received a quote that seems high or low without a clear explanation of what the line items cover. A quote that doesn’t break out the stucco repair, the permit cost, and the window unit separately is a quote that has room for surprises.
Ask about utility rebates. Southern California Edison and the California Energy Commission both maintain rebate programs for qualifying energy-efficient window installations. The programs change year to year, but in 2025 and into 2026, homeowners replacing single-pane windows with Title 24-compliant double-pane low-e units in qualifying homes have been eligible for rebates ranging from $25 to $75 per window. It’s not a large number per unit, but on a twelve-window project it can offset a meaningful portion of the permit cost.
For an accurate written price on your Long Beach home, call (424) 567-7009. The estimate is free, the price is in writing before anyone starts, and the scope covers every line item including stucco repair and permits – no number gets added after the fact.
What the Installation Process Looks Like
Understanding the sequence helps you evaluate a quote and know what to expect on project day.
The process for a standard pocket replacement in Long Beach starts with measurement – accurate rough opening dimensions taken at the widest and narrowest points, because older homes are rarely perfectly square. The window unit is then ordered to match those dimensions. Lead times on stock vinyl windows from Milgard or Simonton run five to ten business days; custom or specialty units from Pella or Marvin can run four to eight weeks. The written quote and scope you receive from Rowan will specify the product and the expected lead time so the schedule is known before you sign.
On installation day, the crew removes the interior stop trim, lifts out the existing sash, checks the condition of the frame pocket, and installs the new unit with shims, low-expansion foam, and flashing tape at the sill and jambs. On the exterior, the stucco is cut back if needed, new backer rod and sealant are applied, and the weep screed is set at the sill to allow any water that gets behind the frame to drain rather than accumulate. Interior trim is reinstalled and caulked. The documented photo record – taken before, during, and after – goes to you as part of the standard deliverable. Not an upgrade. Standard.
For a full-frame installation, the process adds framing inspection, new rough sill and king stud work where needed, and a more involved exterior stucco patch. In the older homes on properties like those in the Rose Park or Bluff Park historic districts, this step sometimes surfaces deferred framing issues – sill rot, water-damaged sheathing – that weren’t visible until the frame came out. Under the Haven Standard, no additional scope proceeds without a signed change order. You see what was found, in writing, with a photo record, and you approve or decline the additional work before it starts.
Comparing Window Brands Available in Long Beach
Rowan’s sourcing depth across fifty-plus vetted brands means the written quote can put real product names and real product costs on paper. The brands most commonly specified for Long Beach residential projects:
- Milgard Windows and Doors – manufactured regionally, strong warranty structure, solid mid-range vinyl and fiberglass lines. The Tuscany Series vinyl and Style Line Series are the most common specifications on Long Beach replacement projects. Lead times are typically shorter than East Coast brands.
- Pella Windows and Doors – broader material range including wood-clad and fiberglass, strong thermal performance specs. The 250 Series vinyl is competitive in price; the Impervia fiberglass line is a good fit for coastal Long Beach properties within a mile of the water.
- Simonton Windows – reliable mid-market vinyl, competitive on cost, available through regional distributors with reasonable lead times. Common choice for straightforward pocket replacements on budget-sensitive projects.
- Marvin Windows and Doors – premium tier, wood and fiberglass, specified on higher-end Bluff Park and historic district projects where the window profile needs to match original architectural details.
- Andersen Windows and Doors – the 400 Series wood-clad and 100 Series Fibrex composite are both solid performers. The Fibrex material holds up well in coastal humidity.
The brand and product series will appear on your written quote with the product specification sheet attached, so the window going in your home is documented before the installation day. If a permit inspector asks for the product’s Title 24 compliance documentation, it’s already in the file.
Permits and Code Requirements in Long Beach
The City of Long Beach Building and Safety Bureau requires a permit for window work that creates a new opening or alters the size of an existing rough opening. Straight-swap replacements – same unit size, same location – are typically exempt but the work still needs to meet Title 24 performance requirements.
For projects in Long Beach’s Historic Preservation Overlay Zones (HPOZs), which include portions of Rose Park, Bluff Park, and the Willmore City area, exterior alterations including window replacement may require approval from the Cultural Heritage Commission before a permit is issued. This adds time to the schedule – typically two to six weeks for HPOZ review – and sometimes limits the window configurations and materials that can be used on street-facing elevations. If your property is in an HPOZ, the written quote and scope will note the review requirement and the timeline impact.
Impact-rated windows installed in designated coastal wind zones require product specification sheets that document the design pressure rating and missile impact test results. The product sheet goes into the permit application and stays in the job file.
FAQs: New Window Installation Cost in Long Beach
How much does it cost to replace all the windows in a Long Beach house?
Replacing all the windows in a typical Long Beach single-family home – usually eight to twelve windows – costs $4,500 to $15,000 depending on frame material, glass package, and whether the work involves pocket replacements or full-frame installations. Vinyl double-pane projects land in the lower half of that range; fiberglass or wood-clad projects with full-frame work in older homes land in the upper half. Call (424) 567-7009 for a written flat-price estimate specific to your home’s window count and condition – the quote is free and the number is in writing before anyone starts.
Do I need a permit to replace windows in Long Beach, CA?
Straight-swap replacements – same window size, same location – are typically exempt from a permit in Long Beach, though the installed window must still meet Title 24 energy code requirements (U-factor 0.30 or lower, SHGC 0.23 or lower for Climate Zone 8). Any project that changes the rough opening size, adds a new opening, or involves structural modifications requires a permit from the Long Beach Building and Safety Bureau. Permit costs run $150 to $500 per permit. Rowan pulls permits and coordinates inspections as a standard step – the cost is included in the written quote, not added later.
How long does window installation take in Long Beach?
A standard pocket replacement runs one to two hours per window for an experienced crew. A whole-home project of ten windows is typically completed in one to two days. Full-frame installations take longer – plan for two to four hours per opening including stucco repair and curing time. Projects in Long Beach’s HPOZ districts may have longer lead times due to the Cultural Heritage Commission review process, which can add two to six weeks before the permit is issued and the installation crew can be scheduled.
Are impact windows required in Long Beach?
Impact windows are not universally required in Long Beach, but homes in designated Coastal Wind Exposure zones and certain high-wind areas may need windows that meet specific design pressure ratings under California Building Code. Even where they’re not strictly required, impact-rated windows are worth considering for properties in Belmont Shore, Naples, and the Peninsula – the laminated glass provides additional security and noise reduction from coastal wind and traffic, not just wind load protection. Impact window installation in Long Beach runs $8,000 to $25,000 for a whole-home project, or $900 to $2,200 per single window. Call (424) 567-7009 and Grant Rowan’s team can tell you whether your address falls in a zone with specific requirements.
Is it cheaper to repair or replace windows in Long Beach?
For windows with failed seals (visible fogging between panes), damaged hardware, or minor frame cracks, repair costs run $150 to $500 per window and can extend the window’s life by several years. But if the frame is rotted, the glass is single-pane, or the window no longer meets Title 24 energy requirements, replacement is the more cost-effective path – you’re paying for repairs on a unit that will need to come out anyway. The diagnostic step costs nothing: when Rowan’s team measures for a quote, they document the condition of each existing frame with a photo record and note which windows are repair candidates vs. replacement candidates. That written assessment goes to you before any work is proposed.
What’s included in Rowan’s window installation quote?
The written flat-price quote covers the window units (specified by brand, series, and product number), labor, hardware, flashing and sealant materials, stucco patch on the exterior where needed, interior trim reinstallation, permit fees where required, and the documented photo record. There is no separate line item added after installation for stucco repair or disposal of the old windows – those costs are in the written price before the crew arrives. Under Clause 1 of the Haven Standard, no work starts without that written price in hand. If something unexpected is found during installation – rotted framing, for example – no additional work proceeds until a change order is written and signed.
Rowan Construction Group Long Beach: The Process in Plain Terms
Grant Rowan started Rowan Construction Group in 2007 with one operating rule: the price is in writing before anyone picks up a tool. Across more than 4,000 projects since then – covering seven residential trades from New Window Installation in Long Beach to kitchen remodeling, roofing, and ADU construction – that rule hasn’t changed. The home page describes the full scope of trades and the Haven Standard that governs every project.
For window projects specifically, the process is: free on-site measurement and condition assessment, written flat-price quote with product specifications named, signed agreement before any material is ordered, permit application where required, scheduled installation with a uniformed background-checked crew, documented photo record delivered at completion, and the 365-Day Done Right Promise in writing on the project paperwork. If something isn’t right within the first year, Rowan makes it right – that’s backed by the Haven Standard, not a handshake.
Long Beach homeowners in Bixby Knolls, Signal Hill, Belmont Shore, Wrigley, Park Estates, El Dorado Park, and across the city have received written quotes from Rowan that included every line item before the first window came out. The same process applies to your project, whatever the scope.
Call (424) 567-7009 to schedule a free estimate. The price will be in writing. Every line item. Before anyone starts.
Written by Grant Rowan, Owner at Rowan Construction Group Long Beach, serving Long Beach, CA since 2007.
Pricing reflects the Long Beach market as of 2026. Rowan Construction Group Long Beach offers free estimates – call (424) 567-7009.
What Our Customers Say
"They found an old septic line under the driveway run and stopped, documented it, and re-quoted before continuing."
- Xavier L."Fence and retaining wall along a sloped boundary. They photographed the footing depth at each post, which mattered when the county inspector came."
- Iona F."Driveway replaced properly with a base that will actually last. They explained why the cheaper quote was cheaper."
- Reggie O.